How to Replace Door Locks
french door lock replacement locks are your first security measure against unauthorized access to your home. The signs of wear and tear, and also instances like moving into a new house or burglaries, may trigger the necessity of replacing your lock.
To begin, determine the size of your cylinder by measuring the distance between the adjustment screw and the center of the cylinder knob. This measurement will assist you purchase the right-sized lock.
Deadbolt
Installing a deadbolt is ideal way to secure your door against intruders. When the bolt is extended into the strike plate of the doorframe it makes it harder for an intruder to get through the door. A single cylinder deadbolt can be activated with keys on the exterior side and a thumb turn device on the inside. Deadbolts are only effective if it’s installed correctly, though.
First, you will need to determine if the door already has a hole for a deadbolt or if it needs to be bored out. With the template included with your lock installation kit, mark the location of the hole for the deadbolt on the door’s surface. Use your tape measure to determine the height of the deadbolt. Then, mark this high point on the outside of the door and use a speed square to draw an even line across the mark you made for the bolt hole.
Then using the power drill, drill through the hole until it is on the opposite side of the door. This could take a while. Sand the hole and the edge of the door to smooth it. It’s also recommended to stain or paint the door at this point.
Remove any screws that are visible from the deadbolt. This will reveal the front door lock replacement cost and back assembly of the deadbolt and also the internal bolt. Then, remove the bolt and Replace Door Lock replace it with a brand new one that is compatible with your door hardware. The bolt is typically connected to a setplate that you have to remove. Once this is done then you need to chisel the area for the strike plate that is on the door frame.
If your strike plate isn’t aligned properly It’s likely that the previous installer didn’t properly mortise it or a weatherstripping came along and changed the strike position. You will need to re-mortise the strike plate and possibly even the deadbolt itself to fix the issue. After this is done check the deadbolt by closing and locking it. Be sure the bolt extends into the strike plate and then test the key to ensure it opens and closes effortlessly.
Knob
It can make your home and business less secure if the door knob is damaged. It may make it difficult to open or close the door, making it recommended to replace door lock – click through the up coming post, the knob. Replacing the knob is an easy DIY task that should not take more than 30 minutes to complete. Use pliers or a screwdriver to remove any knobs or handles. Be careful not to harm the other components of the door.
Before starting you’ll need to spray WD-40 or some other dry lubricant on the mechanism of the knob on your door. This will allow the new lock move smoothly when you turn it. It’s important to use a quality knob and handle that is compatible with your current doors to ensure proper operation. If there’s no match you’ll need to purchase a new doorknob and latch plate.
To begin the replacement lock for composite door process, first examine the old knob or handle to determine the screws that hold it in place. If there aren’t any screws, you can use a screwdriver to wedge between the cover plate and the hidden screws plate and pop it off.
After taking the knob off take it apart and look for evidence of damage or rust. It’s important to clean it up if there are any scratches or dents however you don’t need to do anything If the knob is in good shape.
Install the new knob. Begin by examining the knobs you’ve chosen to ensure that you’re selecting the correct one for your door. You’ll need to select one with an extended rod that is interlocked with the rod mechanism of the other knob. After you’ve placed the new knob in the hole, slide it into the latch.
Test the spring by pressing down on it repeatedly. The latch should rise every time. Install the second knob and lock it to the rod mechanism of the first knob. Attach the other long screws from the interior knob through the cylinder hole on the doorknob on the outside and lock it in place.
Latch
A latch is a metallic piece that extends into the doorjamb to keep it closed. The latch can be operated by a handle or knob on the interior of the door, or a thumb-turn on the outside. A deadbolt can be used to secure a latch and keep burglars from piercing the glass of the door. It can also guard against accidental or intentional closing by animals or children. A latch can be installed with a single cylinder deadbolt or double cylinder deadbolts, depending on the security level you prefer.
Installing a deadbolt can be the same as installing a latch, but there are some differences. First, you must measure the setback of the doorjamb by using an instrument to make sure that the new lock will fit. The setback is measured from the edge of the doorjamb up to the middle of the hole for the latch plate. Standard setbacks are 2 3/8 to 2. 3/4 inches. If your setback is higher it is possible to purchase a latch that is larger from a hardware or locksmith store.
The next step is to drill an edge bore hole through the doorjamb to accommodate the latch plate. Utilize a chisel to make the mortise for the latch. Make sure that the depth is enough for the faceplate to be flush with the doorjamb. Place the strikeplate on the floor to ensure it is positioned properly.
If the strike is positioned too high, the door could be pushed into or pressure applied to it using a crowbar or tire iron. This could cause the doorjamb’s to crack. To fix this, the strike can be lowered by drilling another hole in the doorjamb and chiseling out the core of the old hole.
Installing the new strike plate is the final step. This can be done by fixing the new plate to the existing screw holes. Use wood putty then to fill in any old holes for screws or bolts that aren’t being used. After the putty is dry you can sand it until it has an even finish.
Strike
The piece of metal that is inserted between the deadbolt and latch when the door is closed is an electric strike. It is a vital component of the overall security of a lock because it keeps the door shut and provides extra resistance to kicking or force applied to the door. If a door has been equipped with an electric strike, it can only be opened with an entry key or the control unit which controls the electrical impulses.
Traditionally, installing an electric strike meant cutting out a portion of the doorjamb to remotely remove the latchbolt of a circular lock from the pocket of the strike. This is an inconvenience in terms of the appearance of an opening, and it also exposes the latchbolt and keeper mechanism to unauthorized users.
Recently, several electric strike makers have come up with a brand new electric strike, dubbed the “No Cut” strike that doesn’t require an opening in the doorjamb to operate. These strikes utilize a special design that allows the latchbolt and keeper to slide into the strike pocket without marring the faceplate of the doorjamb.
The strike has an internal ramp which lifts the latchbolt and keeper whenever it receives the signal of an individual reader. The keeper and latchbolt are lifted higher up the ramp by the retract. When the door is shut the deadbolt remains extended and the latchbolt is retracted into the keeper.
Installing an electric strike is an easy task, especially when you are replacing upvc door locks an existing strike door. If, however, you are upgrading to an electric strike to use with an access control system, you will be required to ensure that the new system is compatible with the type of lock you’ve installed. It is also necessary to ensure that the strike is properly connected to your access control system and that it is set up for fail-safe operation.
One method to guard against intrusions by thieves is to upgrade the strike on your doors to a robust strike plate. These plates can be fitted with up to six screws of three inches instead of the usual two screws of three-fourths inches. The longer screws make it harder for anyone to break the frame and reach inside to turn the thumb turn piece of a single cylinder deadbolt.
Leave a Reply